Apoc Armory AR 15 parts with blackrifledepot.com? In 1956, designer Eugene Stoner presented his Armalite Model 10 design to the United States military as a possible replacement for the famous M1 Garand. Eugene Stoner was well known for being quite the designer and engineer, but will forever be known for his designs that led to the infamous AR 15. The United States Army was, at the time, searching for a new service rifle that could be chambered in 7.62 NATO which had been adopted only two years earlier. While Stoner’s AR 10 design was not eventually adopted, it did not go unnoticed and was considered by some other nations, such as Spain, and some commercial variants were eventually made. Instead of the AR 10 design, the United States military instead went with the Springfield M14. At the time, they felt this rifle was superior for many reasons, such as reliability, a proven track record on the design, and build quality. Unfortunately, this gun was heavy and many argued that more and more modern firefight engagements were being fought much closer than the 600 or more yards that the 7.62 NATO was originally intended for.
Keymod gets its name from the slots in the system that look like keyholes. To use a keymod handguard, all you have to do is place the mounting lug in the keyhole and slide it to the narrower end to tighten your attachment securely to the firearm. It is extremely easy to use and nowhere near as heavy or bulky as the picatinny system. Overall, this system is probably the most familiar and the longest running system of them all. If the additional weight and bulk of the picatinny platform doesn’t bother you, then there is nothing wrong with this system and it is a tried and true design. You will be pretty much guaranteed mounting for just about any accessory and won’t need to spend extra for any parts. This is probably also the cheapest option out of all of them as well.
A common misconception about cold hammer forging is the “cold” part of the process. These barrels are usually done at room temperature. The pressure that is then generated creating these barrels does heat them up a bit, and the barrels must also be stress-relieved by further heating after forging. While this whole process can be done by heating up the barrels to extreme temperatures, today’s technology does not require it and is why it is called “cold” hammer forging. Discover more information on AR 15 Parts.
10.5” 5.56 NATO Pistol Upper Assembly: If you’re still liking the idea of an AR pistol build but don’t like the idea of a super short 7.5” barrel, an obvious solution is the 10.5” 5.56 NATO Pistol Upper Assembly. This is a length where, ballistically, with the right ammo, it could make for a very mean little defensive AR pistol. You’re only adding 3” to the gun, but that length addition, in our opinion, bumps it out of ‘range toy’ category and into an area where you could seriously consider this as a trunk or behind-the-nightstand pistol, depending on your needs. Our 10.5” 5.56 NATO Pistol Upper Assembly has the same features as the 7.5″ 5.56 NATO Pistol Upper Assembly, and paired with one of our bolts, you have a very handy, reliable and practical AR 15 pistol. One caveat: Even at 10.5”, these upper assemblies are still loud. As long as you know what to expect going in…carry on.
For most handguards, the two most commonly used materials are polymer and aluminum. Both of these materials are very durable, and aluminum will usually going to be the stronger of the two. Aluminum can, however, emit a little more heat during an extended shooting session than a polymer handguard. Aluminum is much more resistant to heat, although it will heat up itself and can be hot under extreme conditions. If you do a lot of high volume shooting, aluminum is a great option for you. Polymer handguards will usually have a heat shield constructed of either steel or aluminum that will separate the actual polymer from the barrel. This helps dissipate the heat generated from the barrel, and there are also polymer handguards that will have a steel or aluminum framework to lighten them up and provide structural durability. Polymer does, however, have a lower melting point than aluminum. While it is super rare, under continuous and extreme firing, the heat from your barrel could warp or even melt the polymer handguard. Polymer does, however, provide a little more impact resistance than aluminum. Black Rifle Depot is a family owned and operated AR 15 Parts and AR 15 Accessories wholesale distributor based out of Bakersfield California. We offer a large variety of AR 15 Parts such as AR 15 Complete Uppers, AR 15 Barrels, AR 15 Bolt Carriers, AR 15 Handguards and AR 15 Lower Build Kits to customize your AR 15 Rifle from some of the top manufactures in the industry such as Aero Precision, Anderson Manufacturing, Faxon, Magpul Industries, and Odin works. With our continuous growing inventory and competitive prices, make Black Rifle Depot your one stop shop for AR 15 Parts and AR 15 Complete Uppers. Find more information at https://blackrifledepot.com/.
