High quality welding equipment online store Ireland 2021? Ireland market choice: Hobart is an American welding company that has produced quality machines since its inception in 1917. Often toted as the best MIG welder for beginners, the Handler 140 is an affordable and easy to use machine right off the bat. Though its duty cycle is on the low end when compared to the other welders on this list, the Handler is a crowd favorite. It is also fairly easy to carry. Welders will love the portability and ease of use. A home hobbyist will get years of use and enjoyment from this powerful machine. All in all, it’s a very sturdy machine and is manufactured in the USA.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.
Looking for the best Tig welders Ireland? The Hobart Handler 140 is a bit of a hybrid between pro-level performance and homeowner convenience. The 140-amp rating is enough to weld up to 1/4-inch steel. This machine works both as a flux core welder and as a MIG. The duty cycle is 20 percent at 90 amps. That’s enough power to do most jobs you’ll ever tackle in a home shop setting, but for professionals working on heavy stuff like trailer frames or pipe fencing, it’s just not going to be enough. For other professional work like auto body or welding brackets, mountings and the like, this machine can run off a 4000-watt generator. It’s small enough to carry into a home for HVAC repair and the 110/115/120 input means you could use a small generator or the household receptacle to do the work. The solid aluminum wire drive accommodates either 4 or 8-inch spools and it’s selectable between multiple gauges of wire. The Hobart Handler 140 is backed by a 3-year warranty and its professional features and true MIG capability make it the our Pro Value Pick in this review roundup.
The story of ESAB is the story of welding. When our founder Oscar Kjellberg developed the world’s first coated welding electrode in 1904, he launched a company whose innovation and uncompromising standards have helped create the history of welding itself. For more than 100 years, ESAB has been powered by the will to continuously seek new and improved ways of serving our customers. This has made ESAB a world leader in welding products and advanced cutting systems. In 2012, ESAB was acquired by Colfax Corporation, one of the world’s leading diversified industrial manufacturing companies. Colfax, like ESAB, is a solidly customer-focused company that places strong emphasis on constant innovation and improvement. From the firsts by our founder to our global growth, we take pride in what we’ve accomplished in more than a century. But we do so with a keen eye on the future. What can we do better? It’s only when we seek to build upon all we’ve learned, to perfect the innovations our customers count on to work confidently, and push ourselves and our company further that we can boldly face the future. This is how we continue to write the history of welding and cutting. At the end of the day, it’s not where you’ve been that matters most – it’s where you’re going. And for us, that’s forward.
How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).
Several tips on welding equipment, MIG and TIG welders, plasma cutters. The welding setup, welder settings, and electrode selection will impact how fast welders can work. Industrial welders invest time in planning the size and shape of their welding areas, how parts are laid out, and how they supply their shielding gas. Testing settings or an electrode on a piece of scrap metal, especially for a beginners, will save time in the long run. Learn more about setting up an efficient shop here. Welding Downhill Increases Welding Speed: While welding downhill is a faster way to weld, it’s not as strong as welding uphill. On most projects it’s not worth sacrificing strength and durability for the sake of welding speed. However, if the metal is thin enough, then welding downhill won’t make the weld weaker and may even be the correct technique for the job. Learn about uphill and downhill welding and see these diagrams of vertical and downhill welding.
Welding Supplies Direct are the Ireland distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.
Another quality machine from Hobart that has 25A for 190A output range so you can weld up to 5/16 in steel. The power input is only 230V so you won’t be able to use this on your standard household power outlet. The 190 is a wise choice if you’re considering buying a 140A welder but think you may want to upgrade in the future. It’s not much more expensive and you can always turn the 190 down but you can’t turn a 140 up. There’s loads including for the price, you get power, durability, a good duty cycle and all the extras you need to get started, including .030 contact tips, 0.30 flux cored wire and gas gauges. See the full review here.
The people behind Display4top market this particular model as a professional MIG welder and we can’t say that they make a poor case in that regard. For one, its duty cycle is definitely up there. With its 48A rated output, the model is able to work for 6 minutes straight before overheating. It comes equipped with a variable wire speed control trigger, so you’ll be able to efficiently work with different metals. There are two power settings and an Ampere knob, further making the versatility case. More importantly, the model is as durable as they come. The forced air cooling system keeps the temperature at a nice, practical level. On top of that, the welder incorporates a thermal overload protection system that will be able to pick up the former’s slack in case it fails to do its job. See more info at this website.
If you know that your new machine comes with a 2-year warranty, it can take a lot of the stress off your shoulders if your device suddenly stops working. If you can’t find a MIG welder with an appropriate warranty and the right features, it’s often a good idea to choose something that has spare parts which are easy to find. Try not to buy anything that’s made outside of the UK. The price range may be more affordable but the parts would be harder to source. Look for a spool gun so you can weld aluminium. If you plan on using your home welder to weld aluminium, then you’ll need a standard spool gun. Aluminium can quickly become damaged and tangled with a typical welding wire feed spool, so a spool gun will ensure that you can get the best results from your DIY work.
